4″ Aluminum Internal Air Emergency Valve (4″ Air Cylinder) – 90 Degree Elbow
Betts internal air emergency valve meets HM183 requirements for an internal self-closing stop valve. Body is constructed of aluminum and incorporates a shear section that satisfies 49CFR178.345-8 tested per TTMA RP 84. The 1/8” NPT air inlet is designed to shear and close the valve in the event of an under-ride accident. A fusible plug is installed to dump air pressure if temperatures exceed 212°F.ŧŧ Valve uses Teflon® encapsulated seals for compatibility with a wide range of products. Other seal options are also available. Internal air cylinder saves space on exterior of valve providing maximum clearance for piping. Valve is equipped with stainless steel jackscrew that allows for manual operation in the event of an air system failure.
The Maximum Operating Pressure is defined as the maximum tank pressure that valve can open against w/ given air line pressure. Maximum Operating Pressure is 35 psi with 80 psi line pressure and 45 psi with 100 psi line pressure. The Valve MAWP is 35 psi [2.4 bar] and the Minimum Bursting Pressure is 140 psi [9.7 bar].
Product Details
| Assembly No. | Inlet Flange (4" Sump) | Outlet (4" TTMA) | Dimensions | Weight | Fb-MAX Per TTMA RP86 |
|---|---|---|---|---|---|
| EV46921AL** | B.C.: 7.25" [184mm]" 8 Holes: .563" Dia. [14.3mm] | B.C.: 4" GROOVED O.D. 4.5" [114.3mm] 8 Holes: 4" GROOVED O.D. 4.5" [114.3mm] | A: 4.38" [111.3mm] B: 6.25" [158.8mm] | 10.6lbs [4.0kg] | 44,400lbs. [20,140kg.] |
| EV46922AL** | B.C.: 7.25" [184mm]" 8 Holes: .563" Dia. [14.3mm] | B.C.: 5.88" [149mm] 8 Holes: .438" Dia. [11.1mm] | A: 4.38" [111.3mm] B: 5.00" [127.0mm] | 10.9lbs [4.1kg] | 44,400lbs. [20,140kg.] |
| * Values shown are test values. Actual values may vary due to service conditions. ** Last two letters of part number designate seal material as shown on table below. ŧŧ Fusible plug melts at 212°F [100°C]. If valve is subject to higher temperatures, the fusible plug must be relocated to isolate fusible from heat. Caution: Valve must be properly installed and maintained. Never bottom load through emergency valve without first opening valve. Failure to do so may result in damage to the tank and/or valve. |
|||||
| Part # Suffix | Description | Valve Temp. Range * ŧŧ |
|---|---|---|
| TS | Teflon product contact seals, nitrile interior seals, and polyurethane air piston seal | -40°F to +220°F [-40°C to 104°C] |
| TS030 | Teflon product contact seals, FKM "A" interior seals | 5°F to +400°F [-15°C to 204°C] |
| TS038 | Teflon product contact seals, fluorosilicone interior seals, and polyurethane air piston seal. | -50°F to +220°F [-45°C to 104°C] |
| VB | FKM "BLT" product contact seals w/ polyurethane air piston seal. | -15°F to +220°F [-45°C to 104°C] |
| VF | FKM "GFLT-s" product contact seals w/ polyurethane air piston seal | -11°F to +220°F [-24°C to 104°C] |
Engineering Bulletins
EB-01-12: Water Flow Rates of Betts Emergency Valves
EB3-00: MAWP and Bursting Pressure Ratings for Betts Valves
EB2-14: Jack Screw Usage Instructions for Internal Air Emergency Valves
EB4-12: Modification of Internal Air Emergency Valve Breather Port
EB1-11: Important Design Modification Alert for Betts Internal Air Valves
EB1-03: Air Emergency Valve System
Videos
MV-EV001 Internal Air Emergency Valve Rebuild